Valkyrie Riders Cruiser Club
July 19, 2025, 09:40:08 PM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Homepage
:
Photostash
:
JustPics
:
Shoptalk
:
Old Tech Archive
:
Classifieds
:
Contact Staff
News
: If you're new to this message board,
read THIS!
Home
Help
Search
Login
Register
Valkyrie Riders Cruiser Club
>
General
>
1500 Tech Board
>
Galfer brake lines installation related question
Pages: [
1
]
Go Down
« previous
next »
Author
Topic: Galfer brake lines installation related question (Read 1320 times)
Francois_VRCC863
Member
Posts: 7
Galfer brake lines installation related question
«
on:
August 19, 2010, 10:00:53 AM »
Hello,
There is an additional bleeder located on the T block at the lower triple tee. Do I have to also bleed the system at that point or the two lower bleeder should be sufficient ?
TIA
F.
Logged
Joe Hummer
Member
Posts: 1645
VRCC #25677 VRCC Missouri State Representative
Arnold, MO
Re: Galfer brake lines installation related question
«
Reply #1 on:
August 19, 2010, 10:13:36 AM »
Bleeding to the Calipers is the preferred method. There is not a bleeder on the t-block under the triple trees.
Joe
Logged
1999 Valkyrie Interstate
You pay for the whole bike, why not use it Jerry Motorman Palladino
Francois_VRCC863
Member
Posts: 7
Re: Galfer brake lines installation related question
«
Reply #2 on:
August 19, 2010, 10:30:36 AM »
thanks Joe
there is a third bleeder in the kit I got from them as could be seen ther:
http://www.galferusa.com/WebExchange/Standard%20Brake%20Line%20Kits/HONDA/FK003D49-3.pdf
(even if this pdf is not the Valk it's similar)
F.
Logged
Joe Hummer
Member
Posts: 1645
VRCC #25677 VRCC Missouri State Representative
Arnold, MO
Re: Galfer brake lines installation related question
«
Reply #3 on:
August 19, 2010, 10:41:04 AM »
Ummm...interesting. I am not sure what the purpose of that one would be. Approximately 1/2 of the brake fluid in the system is in the calipers. The other half is in the reservoir. Bleeding the line in the middle of the system does not make sense to me. Maybe someone will chime in with a reason I am not familiar with (I really hope so...).
Joe
Logged
1999 Valkyrie Interstate
You pay for the whole bike, why not use it Jerry Motorman Palladino
Francois_VRCC863
Member
Posts: 7
Re: Galfer brake lines installation related question
«
Reply #4 on:
August 19, 2010, 03:15:26 PM »
Just to follow on:
Okay I didn't use this third bleeder but was not very happy with the final feeling at the lever (like if some air bubbles left in). I tried what is suggested on Galfer site: strapping for a couple of hours the brake lever (the idea : detect leaks) and everything is now perfect and not leaking.
Thx all
F.
Logged
Joe Hummer
Member
Posts: 1645
VRCC #25677 VRCC Missouri State Representative
Arnold, MO
Re: Galfer brake lines installation related question
«
Reply #5 on:
August 19, 2010, 04:47:08 PM »
The trick I use to get trapped air out is after bleeding the brakes is to push the piston on the caliper, pump the brakes up, push the caliper in...pump the brakes...I normally only have to do that twice and the brakes feel rock solid after 1/2" or so of travel.
Joe
Logged
1999 Valkyrie Interstate
You pay for the whole bike, why not use it Jerry Motorman Palladino
Robert
Member
Posts: 17042
S Florida
Re: Galfer brake lines installation related question
«
Reply #6 on:
August 19, 2010, 04:48:37 PM »
Hate to contradict but the t does have a bleeder and its good to bleed through there too. have them and had a problem with it. Could probably post a pic if you wanted to see.
Logged
“Some people see things that are and ask, Why? Some people dream of things that never were and ask, Why not? Some people have to go to work and don’t have time for all that.”
Joe Hummer
Member
Posts: 1645
VRCC #25677 VRCC Missouri State Representative
Arnold, MO
Re: Galfer brake lines installation related question
«
Reply #7 on:
August 19, 2010, 04:56:59 PM »
Understand Robert...but I was referring to the stock setup.
Logged
1999 Valkyrie Interstate
You pay for the whole bike, why not use it Jerry Motorman Palladino
sandy
Member
Posts: 5392
Mesa, AZ.
Re: Galfer brake lines installation related question
«
Reply #8 on:
August 19, 2010, 05:33:16 PM »
Both of the Galfer blocks are the same. The bleeder in the 2nd block is to plug the 3rd hole in the block. I bled mine there just to burp the small bubble out.
Logged
http://i982.photobucket.com/albums/ae310/sandyal55/ManCave.jpg
Pages: [
1
]
Go Up
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Chapter Boards
-----------------------------
=> Texas Chapter
=> Kansas Chapter
=> Iowa Chapter
=> Florida Chapter
=> SoCal Chapter
=> Northwest Valkyrie Riders
=> British Columbia
=> New England Chapter
=> Arizona Chapter
=> South Dakota Chapter
-----------------------------
General
-----------------------------
=> General Board
=> InZane XXV
=> 1500 Tech Board
=> 1800 Tech Board
=> VRCC Members Memorial Board
=> InZanes past
=> old classifieds