Valkyrie Riders Cruiser Club
November 23, 2025, 03:04:39 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > new brake pad noise normal?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: new brake pad noise normal?  (Read 1119 times)
theredark
Member
*****
Posts: 86

Derry, NH
« on: September 26, 2011, 05:51:30 AM »
Good morning all!  Just got back from a great tri-state 500 mile run this weekend.  Thanks to all that helped me get my front end together for it.  My question is that I notice that my brakes now make a noise that can only be described as cutting metal with a circular saw from a distance.  It's quite faint and I dont notice it at all with the radio on.  When I got home I looked at the old pads I had taken off (fork oil contaminated, half worn) and saw that they were EBC's that the PO had put on.  The new pads are OEM from HDL.  Would that account for the noise difference?  I felt both rotors and they are not hot so no dragging.  Thanks for any insite.   Brad
Logged
2000 Black/Red Interstate
The Anvil
Member
*****
Posts: 5291


Derry, NH
« Reply #1 on: September 26, 2011, 05:54:12 AM »
Are they EBC rotors? Because if they're stock rotors and stock pads there will be a little bit of noise but nothing downright offensive. OEM on EBC rotors OTOH may be.

And are we talking front, rear or both?
Logged
Boxer rebellion, the Holy Child. They all pay their rent.
But none together can testify to the rhythm of a road well bent.
Saddles and zip codes, passports and gates, the Jones' keep.
In August the water is trickling, in April it's furious deep.

1997 Valk Standard, Red and White.
Chrisj CMA
Member
*****
Posts: 14887


Crestview (Panhandle) Florida
« Reply #2 on: September 26, 2011, 06:16:18 AM »
When you compressed the pistons you may have got one crooked.  look to make sure all the pistons are protruding from the caliper body the same amount and at a straight shot to the pad.  If there is a very slight variance (crooked piston) a very hard squeeze of the handle while NOT moving should straighten it
Logged
98valk
Member
*****
Posts: 13661


South Jersey
« Reply #3 on: September 26, 2011, 06:54:05 AM »
OEM pads are sintered bronze as all aftermarket OEM repalcement pads will be for the our bikes.
 so yes u will have a metal to metal scraping noise, it is normal.
can be louder if the disk were not prepped by light sanding before pad install, to remove old brake material and any glazing. if glazed, the noise will not go away until the glazing is removed by sanding.
Logged
1998 Std/Tourer, 2007 DR200SE, 1981 CB900C  10speed
1973 Duster 340 4-speed rare A/C, 2001 F250 4x4 7.3L, 6sp

"Our Constitution was made only for a Moral and Religious people. It is wholly inadequate to the goverment of any other."
John Adams 10/11/1798
bigdog99
Member
*****
Posts: 584


1/1/2011 86,000 miles

Kouts Indiana
« Reply #4 on: September 26, 2011, 02:36:56 PM »
also look at the pad holder, for lack of other terms. its the part that fits on to the pad and aligns it into the holder. i put on a set and didnt realize 1 of the arms folded under and actually rubbed the rotor.
its the small thin piece of metal that clips onto the pad. not sure the name.  uglystupid2
Logged

VRCC#31391
VRCCDS0239
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS