Valkyrie Riders Cruiser Club
July 22, 2025, 12:22:52 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
Inzane 17
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Bike Sat 5 years
Pages: 1 [2]   Go Down
« previous next »
Send this topic Print
Author Topic: Bike Sat 5 years  (Read 4092 times)
trout dude
Member
*****
Posts: 1000


Hammond Louisiana
« Reply #40 on: February 26, 2014, 07:02:49 PM »
Skinhead
     Yes every thing looked good and was well with in tolerance when checked.
  Dennis
Logged
trout dude
Member
*****
Posts: 1000


Hammond Louisiana
« Reply #41 on: March 01, 2014, 06:44:20 PM »
Well I got all the parts to start putting the clutch back together. While I was cleaning all the parts for the last time i did find another plate cracked so I had my buddy over night it and now have it all.
 I'm going for a ride tomorrow and will start putting the ole girl back together in the evening when I get back.
  Dennis
Logged
Mr.BubblesVRCCDS0008
Member
*****
Posts: 3025

Huffman, Texas close to Houston
« Reply #42 on: March 01, 2014, 07:41:14 PM »
Did my own clutch rebuild at 160,000. replaced all fiber dics and metal dics too. Took an afternoon but not hard at all.
Logged
JimmyG
Member
*****
Posts: 1455


Tennessee
« Reply #43 on: March 01, 2014, 08:02:05 PM »
Hope all goes well Dennis.
Logged
trout dude
Member
*****
Posts: 1000


Hammond Louisiana
« Reply #44 on: March 03, 2014, 12:27:58 PM »
I would like to thank everyone who helped me with the big fix. I took the old gal on the hwy this morning and ran her about 20 miles (all i could stand 38 degrees 20 mile an hour wind and no windshield). Still have some fine tuning to do but motor, clutch did real well. Will post when it is all done. Still have a lot of cleaning and like I said fine tuning.
  Thanks Dennis
Logged
Skinhead
Member
*****
Posts: 8727


J. A. B. O. A.

Troy, MI
« Reply #45 on: March 03, 2014, 03:48:55 PM »
Way to go!
Logged

Troy, MI
T-Bird
Member
*****
Posts: 2487


A friend is one who takes me for what I am.

Cleveland, Tennessee
« Reply #46 on: March 04, 2014, 03:03:24 PM »
Quote from: trout dude on March 03, 2014, 12:27:58 PM
I would like to thank everyone who helped me with the big fix. I took the old gal on the hwy this morning and ran her about 20 miles (all i could stand 38 degrees 20 mile an hour wind and no windshield). Still have some fine tuning to do but motor, clutch did real well. Will post when it is all done. Still have a lot of cleaning and like I said fine tuning.
  Thanks Dennis

Gee Dennis, it was nothing, call me anytime you need mechanical advice... or you need to get rid of some pralines. Evil
Logged
T-Bird
Member
*****
Posts: 2487


A friend is one who takes me for what I am.

Cleveland, Tennessee
« Reply #47 on: March 04, 2014, 03:09:28 PM »
I almost got between you and Sheila for inzane buddy Evil
Logged
trout dude
Member
*****
Posts: 1000


Hammond Louisiana
« Reply #48 on: March 04, 2014, 03:54:33 PM »
T-Bird
  She made some last night I thought about you and yes you did and I thought that was funny.
 She is going to make some at GOTF so you will get some soon enough buddy. cooldude
   Dennis
Logged
hal47
Member
*****
Posts: 545

INDIANA
« Reply #49 on: March 06, 2014, 04:41:25 PM »
Dennis on my harley I just put back two steel plates to replace the riveted one, couldn't tell any difference,just measure and make sure they are the same thickness.
Logged
trout dude
Member
*****
Posts: 1000


Hammond Louisiana
« Reply #50 on: March 06, 2014, 05:19:27 PM »
Thanks Hal
   Shelia got to take her out yesterday for a little spin and said she loved it and wanted to go again today but it was raining. We will see what happens tomorrow when she gets home.
  Dennis
Logged
Pages: 1 [2]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS