Valkyrie Riders Cruiser Club
January 01, 2026, 01:45:07 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Other Honda models with 1" diameter bars - master cylinder questions
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Other Honda models with 1" diameter bars - master cylinder questions  (Read 1228 times)
Bagger John - #3785
Member
*****
Posts: 1951
« on: October 03, 2018, 01:25:44 PM »
Latest project with my I/S is to Turn It Black(TM), and this involves the master cylinders.

I bought a used pair from a parted-out '04 GL1800, thinking I might use them in place of the stock F6 units. Wrong...they're for a 7/8" bar, although I did get a nice set of black levers with them.

So...here's a question or two for the board:

Are there other Hondas (or any other bikes, for that matter) which use this style Nissin master cylinder on a 1" diameter handlebar? Are any of those master cylinders found in black?

Back in the day, a lot of people were chroming the stock master cylinders. Doing this required the sight glasses to be pressed out then back into place after the job was finished. Is there a write-up somewhere in the Archives which shows the procedure, in the event one wanted to powdercoat or paint the stock cylinders?

Open to other suggestions as well. Also going to list the '1800 master cylinders in our Classifieds - cheap - unless someone PMs me with an offer I can't refuse.
Logged
hubcapsc
Member
*****
Posts: 16804


upstate

South Carolina
« Reply #1 on: October 04, 2018, 02:13:49 AM »

2014/2015 Valkyrie controls fit nicely on 1997/2003 Valkyrie handlebars...



-Mike
Logged
https://sites.google.com/a/g.clemson.edu/confederate-memorial-day-at-clemson/
Bagger John - #3785
Member
*****
Posts: 1951
« Reply #2 on: October 04, 2018, 04:45:59 AM »
Quote from: hubcapsc on October 04, 2018, 02:13:49 AM

2014/2015 Valkyrie controls fit nicely on 1997/2003 Valkyrie handlebars...



-Mike
Exactly what I was looking for. Thanks, Mike!  cooldude

ETA:

Are those on your bike? If so, what year?
« Last Edit: October 04, 2018, 05:02:51 AM by Bagger John - #3785 » Logged
hubcapsc
Member
*****
Posts: 16804


upstate

South Carolina
« Reply #3 on: October 04, 2018, 05:38:25 AM »

My bike's a black 2014... I don't know for sure, but I bet they
are all the same...

-Mike
Logged
https://sites.google.com/a/g.clemson.edu/confederate-memorial-day-at-clemson/
Bagger John - #3785
Member
*****
Posts: 1951
« Reply #4 on: October 04, 2018, 06:11:48 AM »
Quote from: hubcapsc on October 04, 2018, 05:38:25 AM

My bike's a black 2014... I don't know for sure, but I bet they
are all the same...

-Mike
I went parts fishing this morning after reading your reply and found the 2014 parts. Those will be sourced over the winter.

Thanks again for replying.
Logged
Wayn-O
Member
*****
Posts: 88


Orem, UT
« Reply #5 on: October 04, 2018, 02:06:18 PM »
I've heard of people swapping out the valkyrie clutch master cylinder with a VTX 1800 one because it's apparently easier to pull.  So, that would indicate that VTX 1800s have 1" bars... hope that broadens your search.  Maybe try ebay?
Logged
2000 GL1500C Valkyrie 
2003 VT1100C Shadow Spirit
1998 VT1100C Shadow Spirit
1983 VF750C V45 Magna
Bagger John - #3785
Member
*****
Posts: 1951
« Reply #6 on: October 04, 2018, 03:34:42 PM »
Quote from: Wayn-O on October 04, 2018, 02:06:18 PM
I've heard of people swapping out the valkyrie clutch master cylinder with a VTX 1800 one because it's apparently easier to pull.  So, that would indicate that VTX 1800s have 1" bars... hope that broadens your search.  Maybe try ebay?
The problem is...they're all brushed silver finish.

Trust me, I've beaten eBay to death over the past few days looking for a source for these.  uglystupid2
Logged
TJ
Member
*****
Posts: 1838

Lake Placid , Fl.
« Reply #7 on: October 06, 2018, 10:16:53 AM »
 I have a new set of 1 inch brake & clutch M/C for $60. + $10. shipping...
never used or mounted...   Black
tjranch9 @ gmail.com
Logged
Bagger John - #3785
Member
*****
Posts: 1951
« Reply #8 on: October 09, 2018, 12:10:49 PM »
Quote from: TJ on October 06, 2018, 10:16:53 AM
I have a new set of 1 inch brake & clutch M/C for $60. + $10. shipping...
never used or mounted...   Black
tjranch9 @ gmail.com

Which brand are these?
Logged
TJ
Member
*****
Posts: 1838

Lake Placid , Fl.
« Reply #9 on: October 10, 2018, 12:10:02 PM »
Don't know anymore.. Boxes are gone and don't remember where I ordered them..
They were for a customer's  bike and he totaled it before I got them on...
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS