Valkyrie Riders Cruiser Club
June 25, 2025, 10:19:58 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Accessory Power
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Accessory Power  (Read 1012 times)
Paladin528
Member
*****
Posts: 722


Greater Toronto Area Ontario Canada


WWW
« on: June 25, 2019, 10:25:19 AM »
Ok so I have been looking at the schematic for a long time and keep procrastinating on this.
I have installed an AMP under the fairing to drive the speakers front and rear.  It is triggered off of the switched power on the bike so its on when the bike is on and off when its off.

HOWEVER

I can no longer listen to the radio with the bike OFF (in the ACC position) because there is no trigger power from the ignition to power the AMP.

My question is where is the connector located that provides the power from the ACC circuit on the ignition? 
The schematic looks like its just behind the Ignition switch but I have not dug into it yet.  can anyone identify it?

PS No I am not looking for the accessory plug behind the right side panel.  I am already using that and it is not on the ACC circuit.
Logged
Bagger John - #3785
Member
*****
Posts: 1952
« Reply #1 on: June 25, 2019, 11:11:24 AM »
Look in Das Boot which houses the ignition switch to main harness connector along with the fuel level sender connector.
Logged
gordonv
Member
*****
Posts: 5760


VRCC # 31419

Richmond BC
« Reply #2 on: June 25, 2019, 06:42:18 PM »
It's behind the right side cover.

I forget exactly, but think it's a single male and female bullet connector.
Logged
1999 Black with custom paint IS
9Ball
Member
*****
Posts: 2183


South Jersey
« Reply #3 on: June 26, 2019, 01:56:49 AM »
Quote from: Paladin528 on June 25, 2019, 10:25:19 AM
Ok so I have been looking at the schematic for a long time and keep procrastinating on this.
I have installed an AMP under the fairing to drive the speakers front and rear.  It is triggered off of the switched power on the bike so its on when the bike is on and off when its off.

HOWEVER

I can no longer listen to the radio with the bike OFF (in the ACC position) because there is no trigger power from the ignition to power the AMP.

My question is where is the connector located that provides the power from the ACC circuit on the ignition? 
The schematic looks like its just behind the Ignition switch but I have not dug into it yet.  can anyone identify it?

PS No I am not looking for the accessory plug behind the right side panel.  I am already using that and it is not on the ACC circuit.
Logged
VRCC #6897, Joined May, 2000

1999 Standard
2007 Rocket 3
2005 VTX 1300S
Paladin528
Member
*****
Posts: 722


Greater Toronto Area Ontario Canada


WWW
« Reply #4 on: June 26, 2019, 09:51:52 AM »
Thanks 9ball
Logged
Paladin528
Member
*****
Posts: 722


Greater Toronto Area Ontario Canada


WWW
« Reply #5 on: June 26, 2019, 09:52:37 AM »
Quote from: Bagger John - #3785 on June 25, 2019, 11:11:24 AM
Look in Das Boot which houses the ignition switch to main harness connector along with the fuel level sender connector.

figures....Now I have to run the tank down to lighten it up for removal   Smiley
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS