Valkyrie Riders Cruiser Club
June 22, 2025, 03:44:21 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
VRCC Calendar Ad
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Tail light fender removal
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Tail light fender removal  (Read 1088 times)
AwesomeDad
Member
*****
Posts: 221


TN
« on: July 11, 2020, 10:17:51 AM »
Yes I’ve searched and read. Most topics covered the super Valk conversion. All I want to know is to change the rear fender do you have to cut the wires for the tail light assembly or can the harness be fed thru the opening?

JJ
Logged
indybobm
Member
*****
Posts: 1600

Franklin, Indiana VRCC # 5258
« Reply #1 on: July 11, 2020, 10:26:35 AM »
Wires disconnect at the taillight assembly and the stop light, bullet connections. there is a square connector at the junction of the two rear fender sections.
Logged
So many roads, so little time
VRCC # 5258
AwesomeDad
Member
*****
Posts: 221


TN
« Reply #2 on: July 11, 2020, 11:19:04 AM »
Quote from: indybobm on July 11, 2020, 10:26:35 AM
Wires disconnect at the taillight assembly and the stop light, bullet connections. there is a square connector at the junction of the two rear fender sections.
So worse case I’d just have to replace the bullet connectors...
Logged
gordonv
Member
*****
Posts: 5760


VRCC # 31419

Richmond BC
« Reply #3 on: July 11, 2020, 02:39:19 PM »
Honda bullet connectors are 3.5 mm, not the 4 mm of a standard auto wiring.

http://www.cycleterminal.com/solenoid-connectors.html

http://www.vintageconnections.com/

You should be able to find them on either one of the above sites.
Logged
1999 Black with custom paint IS
AwesomeDad
Member
*****
Posts: 221


TN
« Reply #4 on: July 11, 2020, 03:32:20 PM »
Quote from: gordonv on July 11, 2020, 02:39:19 PM
Honda bullet connectors are 3.5 mm, not the 4 mm of a standard auto wiring.

http://www.cycleterminal.com/solenoid-connectors.html

http://www.vintageconnections.com/

You should be able to find them on either one of the above sites.

Thanks a bunch...
Logged
Hook#3287
Member
*****
Posts: 6429


Brimfield, Ma
« Reply #5 on: July 12, 2020, 04:20:01 PM »
Quote from: AwesomeDad on July 11, 2020, 11:19:04 AM
Quote from: indybobm on July 11, 2020, 10:26:35 AM
Wires disconnect at the taillight assembly and the stop light, bullet connections. there is a square connector at the junction of the two rear fender sections.
So worse case I’d just have to replace the bullet connectors...
No.  You should be able to feed the wires out of the fender after disconnecting them.
Logged
AwesomeDad
Member
*****
Posts: 221


TN
« Reply #6 on: July 13, 2020, 08:16:45 AM »
Quote from: Hook#3287 on July 12, 2020, 04:20:01 PM
Quote from: AwesomeDad on July 11, 2020, 11:19:04 AM
Quote from: indybobm on July 11, 2020, 10:26:35 AM
Wires disconnect at the taillight assembly and the stop light, bullet connections. there is a square connector at the junction of the two rear fender sections.
So worse case I’d just have to replace the bullet connectors...
No.  You should be able to feed the wires out of the fender after disconnecting them.
I’ll give it a try
Logged
Madmike
Member
*****
Posts: 837


Campbell River BC, Canada
« Reply #7 on: July 13, 2020, 08:29:32 AM »
Quote from: AwesomeDad on July 11, 2020, 03:32:20 PM
Quote from: gordonv on July 11, 2020, 02:39:19 PM
Honda bullet connectors are 3.5 mm, not the 4 mm of a standard auto wiring.

http://www.cycleterminal.com/solenoid-connectors.html

http://www.vintageconnections.com/

You should be able to find them on either one of the above sites.

Thanks a bunch...


amazon has them as well if you have Prime
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS