Valkyrie Riders Cruiser Club
July 16, 2025, 10:55:14 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
Inzane 17
Pages: [1]   Go Down
Send this topic Print
Author Topic: used Parts  (Read 1415 times)
kidcatfish
Member
*****
Posts: 120


hold my beer and watch this !!!

Ore City, Texas


« on: June 15, 2010, 07:30:44 AM »

OK, to get started, I have NO affiliation with this person. I just bought brake rotor from him and told the guy I was gonna mention him on this site. I am in northern Arkansas.

I was needing a rear brake rotor. Gonna change out brake pads and did not want to use the very worn rotor again. Called a place near me that is a motorcycle salvage yard about the rotor. Naturally, they did not have one, but gave me a number to a guy that might. Long story short, fella in Searcy, Ar. has all kinds of motorcycle parts, expecially goldwing, valk parts. If you have ever looked up the price of a new rotor from HDL they are $253.  I got one for $60. Now mind you it has a couple of miles on it, thats right, a couple. This guy has parts from new bikes that were triked out.  He also showed me a mustang seat and a stock seat for a valk. He also has loads of factory saddlebags from wings. Told me to mention that he has a lot of complete rears from 1800 wings and that includes the bags and whatever else is back there. He had a complete back wheel that included the rotor and bearings for $100. But it was from a wing and not the same apperance as the valk. Do not know if it would work or not.

John's Cycle
501-207-3976
103 B black Gum Lane
Searcy, Arkansas 72143

Maybe it will help someone.

Logged
Old Geezer Richard
Member
*****
Posts: 1047


San Antonio , Tx


« Reply #1 on: June 15, 2010, 08:52:22 AM »

  Hey Kid Catfish , thanks for the tip , does he ship his parts ? if he does he sure would be alot closer than Pinwall Salvage in Ohio  cooldude Thanks again the Geez
Logged

If you don't care where you're going, then you ain't lost , Murphy's Law because wherever you are going to , it ain't going nowhere ....   San Antonio,Tx.
Earl in Pensacola
Member
*****
Posts: 556


« Reply #2 on: June 15, 2010, 09:18:45 AM »

I've also made note of John's Cycle etc. just in case, even though Pinwall has done me right several times.
Logged
kidcatfish
Member
*****
Posts: 120


hold my beer and watch this !!!

Ore City, Texas


« Reply #3 on: June 15, 2010, 04:04:40 PM »

Sorry , just now gettiin back on. Yes, he will ship (you pay for it of cource) I informed him that would be the case for us to use him. It was the better part of all day yesterday for me to leave Flippin and go to Searcy and back. For those who have rode the roade here in Arkansas, there AINT no direct route to anything !!!  I went in my truck thinking I was going to purchase a complete  back wheel for extra (at that price). But it was a wing wheel, not the same design as the valk wheel, not as beafy in the spoke area. Didnt get one, but bought two brake rotors. Already have one bolted to my wheel, waiting on my brake pads to get here.

Yea, I have used Pinwalls and also had very good service with them. Got to have all the help with parts we can get !!! 
« Last Edit: June 15, 2010, 04:08:59 PM by kidcatfish » Logged
Pages: [1]   Go Up
Send this topic Print
Jump to: