Valkyrie Riders Cruiser Club
August 23, 2025, 11:00:58 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
VRCC Calendar Ad
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > NEED NUT CAGE MOD INFO ASAP
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: NEED NUT CAGE MOD INFO ASAP  (Read 1365 times)
glenh
Member
*****
Posts: 61


SW Minnesotio
« on: June 25, 2011, 06:13:30 AM »
I'm taking a Gen. Altimax 205/60-16in in less than an hour to get installed, I have the 55 series on now, looks like plenty of room for the 60, but just in case, where are the directions for doing the nut mod, I couldn't find them in Shop Talk, i read it someplace, but don't remember. Thanks
Logged
"God created man. Sam Colt made them equal"
Gryphon Rider
Member
*****
Posts: 5227


2000 Tourer

Calgary, Alberta
« Reply #1 on: June 25, 2011, 06:27:20 AM »
Here's Daniel Meyer's version:
http://lifeisaroad.com/stories/2005/08/24/valkyrieRearFenderNutCageMod.html
Logged
glenh
Member
*****
Posts: 61


SW Minnesotio
« Reply #2 on: June 25, 2011, 06:32:52 AM »
That's what I was looking for, thanks, easier than I figured.
Logged
"God created man. Sam Colt made them equal"
B
Member
*****
Posts: 576


Capital Area - Michigan
« Reply #3 on: June 25, 2011, 06:45:27 AM »
Do the mod while the wheel is off and either flip the bolts or put a washer and hex nut on the right side. My '60' rubbed until I did all this.  My2Cents.  B
Logged
"if I ride the morning winds to the farthest oceans, even there your hand will guide me." TLB-Ps.139:9-10
X Ring
Member
*****
Posts: 3626


VRCC #27389, VRCCDS #204

The Landmass Between Mobile And New Orleans
« Reply #4 on: June 25, 2011, 07:22:57 AM »
Quote from: glenh on June 25, 2011, 06:13:30 AM
I'm taking a Gen. Altimax 205/60-16in in less than an hour to get installed, I have the 55 series on now, looks like plenty of room for the 60, but just in case, where are the directions for doing the nut mod, I couldn't find them in Shop Talk, i read it someplace, but don't remember. Thanks

Really?  You couldn't find "Valkyrie Fender Nut Mod"  in Shoptalk?

Marty
Logged
People are more passionately opposed to wearing fur than leather because it's safer to harass rich women than bikers.           
MacDragon
Member
*****
Posts: 1970


My first Valk VRCC# 32095

Middleton, Mass.
« Reply #5 on: June 25, 2011, 12:17:26 PM »
The very last item in Shoptalk.
Logged

Ride fast and take chances... uh, I mean... ride safe folks.
Patriot Guard Riders
glenh
Member
*****
Posts: 61


SW Minnesotio
« Reply #6 on: June 25, 2011, 12:24:38 PM »
Just got my 60 series tire mounted, there is almost 2" from it to the nut cages, no need for any mod. I put 26 lbs of air in it,rides and handles great.
Logged
"God created man. Sam Colt made them equal"
Paxton
Member
*****
Posts: 2507


So Cal
« Reply #7 on: June 25, 2011, 03:10:38 PM »
If you did not have to do the nut cage mod, your shocks are probably at their highest setting.
Notwithstanding, test it.
Get your fattest friend to ride with you as a passenger...  2funny

I hope not, but it might make those 2 inches disappear.
You might also have to increase tire pressure with lots of weight behind you.

Good luck!  cooldude
Logged
J. Paxton Gomez

1966 First year Bronco... 302 CI V8
1975 First year Chrysler Cordoba... 360 CI V8
1978 Honda 750F / Cafe Racer
2000 GL1500CY Fast-Black Standard Solo Rider

So Cal... 91205

"Four wheels move the body; two wheels move the soul."
GOOSE
Member
*****
Posts: 704


D.S. #: 1643

Southwest Virginia
« Reply #8 on: June 26, 2011, 11:54:45 AM »
i run that same altimax.... 26 lbs. seems lite, especially on a new tire.  believe me, when you put any weight on that back end....it's going to rub.
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS