Valkyrie Riders Cruiser Club
November 25, 2025, 08:23:56 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Burnging oil
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Burnging oil  (Read 1118 times)
themetalman03886
Member
*****
Posts: 30


Havelock Nc
« on: May 27, 2013, 04:09:27 PM »
I just finished my ride to Rolling Thunder this year, while I was up there I checked my oil (changed it about 2500 miles ago) I was low, ended up adding about .6 quarts to get her full. Yes I did check it right, bike upright and did not screw in the stick. When I start her up she smokes for a little bit but then it dies down, my brother says when I get on it she puffs out a little bit of smoke too, more from the right side than the left. I am not too worried about using a little bit of oil I am mainly just curious on what is causing her to use oil... My guess is valve stem seals but I am not sure. I have 57000 on her, she runs great and doesn't give me any real problems (speedo cable broke on me while in DC) but I guess I just want some input on what the other forum members think.
Logged
Hoser
Member
*****
Posts: 5844


child of the sixties VRCC 17899

Auburn, Kansas
« Reply #1 on: May 27, 2013, 04:43:58 PM »
Don't know, never heard of that before.  Oil leak maybe?  Broken ring?  Check compression on the right side.  Hoser  Shocked
Logged
I don't want a pickle, just wanna ride my motor sickle

[img width=300 height=233]http://i617.photobucket.com/albums/
F6BANGER
Member
*****
Posts: 835


Albuquerque NM
« Reply #2 on: May 27, 2013, 04:44:28 PM »
First, look for leaks. If you dont find any, do a wet/dry compression test. If your compression goes up your rings are prolly leaking. If it doesnt go up, its prolly your valve stem seals.
« Last Edit: May 27, 2013, 06:36:37 PM by F6BANGER » Logged
themetalman03886
Member
*****
Posts: 30


Havelock Nc
« Reply #3 on: May 27, 2013, 04:47:57 PM »
I have looked for leaks, doesn't leak a drop, I will do a compression test tomorrow, almost a 1000 miles on her this weekend, my butt is tired.
Logged
Patrick
Member
*****
Posts: 15433


VRCC 4474

Largo Florida
« Reply #4 on: May 27, 2013, 05:39:23 PM »
I'll be surprised if a compression test shows anything. Some of these engines do get loose in the valve guides, not a big deal if it blows a little smoke on hard acceleration or initial start-up.
Logged
themetalman03886
Member
*****
Posts: 30


Havelock Nc
« Reply #5 on: May 27, 2013, 06:01:30 PM »
Honestly I will be surprised too, she runs way too strong to be loosing compression, the right side smoking more than the left side also makes me think valve stem seals as it could have sat for a while and the seals dried up.
Logged
Ricky-D
Member
*****
Posts: 5031


South Carolina midlands
« Reply #6 on: May 28, 2013, 10:11:09 AM »
A look at the spark plugs may reveal that there is a problem.

***
Logged
2000_Valkyrie_Interstate
Gryphon Rider
Member
*****
Posts: 5232


2000 Tourer

Calgary, Alberta
« Reply #7 on: May 28, 2013, 01:43:54 PM »
Quote from: F6BANGER on May 27, 2013, 04:44:28 PM
First, look for leaks. If you dont find any, do a wet/dry compression test. If your compression goes up your rings are prolly leaking. If it doesnt go up, its prolly your valve stem seals.
I've never done a compression test, let alone a wet compression test, but is it possible to do a wet compression test on a non-vertical cylinder?
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS