Valkyrie Riders Cruiser Club
September 12, 2025, 10:34:47 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > drive shaft ok?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: drive shaft ok?  (Read 858 times)
al v
Member
*****
Posts: 227


Clinton Township, MI
« on: June 26, 2013, 06:18:13 PM »


Missing one little tooth section above the clip? It was like this when it came out. I'm guessing it is still ok, but thought I would see what everyone thought...

23k miles on bike. Splines looks perfect. Drive flange looks perfect. Ujoint looks perfect. Just this one little issue.

(Splines were wet with drive gear oil. Cleaned the pinion cup and oil is freely flowing into pinion cup.)
Logged
Daniel Meyer
Member
*****
Posts: 5493


Author. Adventurer. Electrician.

The State of confusion.


WWW
« Reply #1 on: June 26, 2013, 06:32:19 PM »
I'd run it.
Logged
CUAgain,
Daniel Meyer
fudgie
Member
*****
Posts: 10616


Better to be judged by 12, then carried by 6.

Huntington Indiana


WWW
« Reply #2 on: June 26, 2013, 07:20:13 PM »
Looks just like mine!  Grin Been good for 30k so far.  cooldude
Logged


Now you're in the world of the wolves...
And we welcome all you sheep...

VRCC-#7196
VRCCDS-#0175
DTR
PGR
Farther
Member
*****
Posts: 1680


Quimper Peninsula, WA
« Reply #3 on: June 26, 2013, 07:24:19 PM »
I suggest you look for the missing bit so it doesn't cause problems.
Logged
Thanks,
~Farther
Mallett
Member
*****
Posts: 511


Oh, what a ride!!!!

Laurel, Mississippi


WWW
« Reply #4 on: June 26, 2013, 07:38:20 PM »
Quote from: Daniel Meyer on June 26, 2013, 06:32:19 PM
I'd run it.


+1
Logged
Any coward can fight a battle when he's sure of winning; but give me the man who has pluck to fight when he's sure of losing.
GEORGE ELIOT
Gryphon Rider
Member
*****
Posts: 5232


2000 Tourer

Calgary, Alberta
« Reply #5 on: June 26, 2013, 09:36:23 PM »
In order to properly balance a motorcycle with this damage, you need to remove one spoke that connects the left side of the rim of the front wheel to the left brake shoe hub, then tighten adjacent two spokes by 1/8th turn to compensate.
Logged
Rio Wil
Member
*****
Posts: 1360
« Reply #6 on: June 26, 2013, 10:28:43 PM »
The piece missing is too big to go down the oil hole and into the final drive......so it either had to be in the pinion cup or laying on the garage floor where some one dropped the shaft and broke it off. 2funny 2funny

Oh yeah....I'd run it with no second thoughts......but, if you are a purist, send it to me for a spare...hehehehehe
« Last Edit: June 26, 2013, 10:30:47 PM by Rio Wil » Logged
Patrick
Member
*****
Posts: 15433


VRCC 4474

Largo Florida
« Reply #7 on: June 27, 2013, 10:41:39 AM »
I wouldn't worry about it either. I'd just clean/smooth it up a bit and run it.
Logged
al v
Member
*****
Posts: 227


Clinton Township, MI
« Reply #8 on: June 27, 2013, 10:55:39 AM »
The drive shaft will be going back on... Thanks for the input.
Logged
biguglyman
Member
*****
Posts: 579


"AN ARMED SOCIETY IS A POLITE SOCIETY"

Brockport, NY


WWW
« Reply #9 on: June 27, 2013, 11:06:52 AM »
Quote
In order to properly balance a motorcycle with this damage, you need to remove one spoke that connects the left side of the rim of the front wheel to the left brake shoe hub, then tighten adjacent two spokes by 1/8th turn to compensate.

All right. That just made me laugh out loud. I'd also use a high-speed taper shank spiral flute reamer to realign the jasper pins when reassembling. Grin
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS