Valkyrie Riders Cruiser Club
September 10, 2025, 01:23:37 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > still no guides or instruction on a fuel rail o-ring replacement?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: still no guides or instruction on a fuel rail o-ring replacement?  (Read 870 times)
cajundood
Member
*****
Posts: 160


Down in da Swamps of Louisiana
« on: May 07, 2014, 01:23:52 PM »
Searched high and wide.

Read dozens of posts on the forum.

Watched countless videos from youtoob...from Dag as well as D-Ray Smith(none of which deal with fuel rail o-ring replacement)


Fuel rail tee on carb #6 still leaking although not very badly. Bought the repair kit from redeye last fall but couldn't find any info on the procedure.....unless i paid someone $500 or more to do it for me... uglystupid2

Isn't there someplace that I could get instruction on this procedure????  ???  ???
« Last Edit: May 07, 2014, 01:26:59 PM by cajundood » Logged
LIFE's BETTER ON THE DARKSIDE
signart
Member
*****
Posts: 2095


Crossville, Tennessee
« Reply #1 on: May 07, 2014, 01:34:14 PM »
I think when I did mine, the Redeye kit had some instruction... I think... maybe.
Logged
rugguy
Member
*****
Posts: 245

2000 Valk I/S

Atlanta, GA
« Reply #2 on: May 07, 2014, 05:31:00 PM »
Clymer Manual is very detailed on this procedure. I did mine a couple of months ago.
Logged
I hate sand....sand SUCKS!

I wear a helmet....."I'd rather have brains in my head than wind in my hair"
1999 Valk I/S
2000 Valk I/S
2001 BMW K1200 LTE (sold)
2002 FLHRSEI (for sale)
2006 FLHCTUI (sold)
Brian
Member
*****
Posts: 996


Monroe, NC
« Reply #3 on: May 08, 2014, 02:58:37 AM »
The Clymer shop manual will be paid for the first time you use it for this service. The carbs have to be separated to do this. Do not touch the synch screws and pay attention to the placement of the small springs that are associated with the gas linkage. Take a lot close up pictures of the assembly you start.
Logged
98valk
Member
*****
Posts: 13586


South Jersey
« Reply #4 on: May 08, 2014, 03:28:31 AM »
download the free factory service manual from the Dag's? norway site.
very easy, pull the carbs apart, pull out the tubes, remove old o-rings, silicon grease aka bulb grease the new o-rings, install in reverse order.
Logged
1998 Std/Tourer, 2007 DR200SE, 1981 CB900C  10speed
1973 Duster 340 4-speed rare A/C, 2001 F250 4x4 7.3L, 6sp

"Our Constitution was made only for a Moral and Religious people. It is wholly inadequate to the goverment of any other."
John Adams 10/11/1798
rugguy
Member
*****
Posts: 245

2000 Valk I/S

Atlanta, GA
« Reply #5 on: May 08, 2014, 07:27:33 AM »
+1 on Brian's advice on the Clymer and the photos....I bought mine new on ebay....worth the $$
« Last Edit: May 08, 2014, 07:37:52 AM by rugguy » Logged
I hate sand....sand SUCKS!

I wear a helmet....."I'd rather have brains in my head than wind in my hair"
1999 Valk I/S
2000 Valk I/S
2001 BMW K1200 LTE (sold)
2002 FLHRSEI (for sale)
2006 FLHCTUI (sold)
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS