|
nswiley
|
 |
« on: May 12, 2014, 12:08:13 PM » |
|
Taking trunk off my interstate, purchased a standard tail light, is there a plug and play for the wiring or do I have to cut and solder? If so where do I find one, looked bit unable to find one. THANKS AGAIN!
|
|
|
|
|
Logged
|
|
|
|
|
Highbinder
|
|
« Reply #1 on: May 12, 2014, 01:46:54 PM » |
|
If you look at the plug on the wiring coming from the trunk for the taillights for the trunk, you will see that it is a 3 prong plug that goes to the connection under the right side cover, you can either buy another matching plug and wire it to the tail light or cut the one off the trunk and wire it to the tail light and just plug it in...only do that if you don't intend to put the trunk back on with a quick disconnect.
|
|
|
|
|
Logged
|
|
|
|
|
blackvalkyrie
|
|
« Reply #2 on: May 12, 2014, 06:05:08 PM » |
|
are you selling the trunk? if so, is it black and do you know if it will fit a 97 valk standard? hows the tailight coming?  Taking trunk off my interstate, purchased a standard tail light, is there a plug and play for the wiring or do I have to cut and solder? If so where do I find one, looked bit unable to find one. THANKS AGAIN!
|
|
|
|
|
Logged
|
|
|
|
|
|
|
Bighead
|
|
« Reply #4 on: May 12, 2014, 08:22:35 PM » |
|
are you selling the trunk? if so, is it black and do you know if it will fit a 97 valk standard? hows the tailight coming? Taking trunk off my interstate, purchased a standard tail light, is there a plug and play for the wiring or do I have to cut and solder? If so where do I find one, looked bit unable to find one. THANKS AGAIN!
Yes they will all fit your bike if you have the mounting Brackets and hardware. |
|
|
|
|
Logged
|
1997 Bumble Bee
1999 Interstate (sold)
2016 Wing
|
|
|
|
blackvalkyrie
|
|
« Reply #5 on: May 12, 2014, 10:23:39 PM » |
|
are you selling the trunk? if so, is it black and do you know if it will fit a 97 valk standard? hows the tailight coming? Taking trunk off my interstate, purchased a standard tail light, is there a plug and play for the wiring or do I have to cut and solder? If so where do I find one, looked bit unable to find one. THANKS AGAIN!
Thanks..love the bumble bee! Yes they will all fit your bike if you have the mounting Brackets and hardware. |
|
|
|
|
Logged
|
|
|
|
|
PhredValk
|
|
« Reply #6 on: May 12, 2014, 11:03:42 PM » |
|
If you put the trunk back on, and install the CB radio under the trunk, it will interfere with the standard tail light.
Just sayin.
Fred.
|
|
|
|
|
Logged
|
Growing old is mandatory, growing up is optional.
VRCCDS0237
|
|
|
|
nswiley
|
|
« Reply #7 on: May 13, 2014, 03:34:36 AM » |
|
Thanks for the info, and sorry keeping the trunk. Happy Ridding!
|
|
|
|
|
Logged
|
|
|
|
|
alph
|
|
« Reply #8 on: May 13, 2014, 07:25:00 AM » |
|
just a suggestion. if you're running a brake light for the tail light, while you've got the whole fender assembly apart, run that same brake light wire to the turn signal area and cap it for future use. when I S/V (super-valked) my I/S I had to run a wire for the same thing, then a year later I had to run a wire from my tail light to the rear turn signals for additional rear brake lights.....
|
|
|
|
|
Logged
|
Promote world peace, ban all religion. Ride Safe, Ride Often!!   |
|
|
|
Jess from VA
|
|
« Reply #9 on: May 13, 2014, 08:23:36 AM » |
|
|
|
|
|
|
Logged
|
|
|
|
|
