Valkyrie Riders Cruiser Club
July 11, 2025, 12:49:11 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
Inzane 17
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Best lube for a couple of different places?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Best lube for a couple of different places?  (Read 1386 times)
doubletee
Member
*****
Posts: 1165


VRCC # 22269

Fort Wayne, IN
« on: October 08, 2015, 07:42:00 AM »
Get your mind out of the gutter!   Cheesy Grin

I think I need to lube my choke (enricher) cable. It's starting to click and is really hard to move. I'm fearful I'm going to snap the cable soon if I don't get it freed up. Lube only at the handlebar, or also down near the carbs?

Also, what's the best lube for the turn signal switch, dielectric grease?
Logged
  
Paladin528
Member
*****
Posts: 722


Greater Toronto Area Ontario Canada


WWW
« Reply #1 on: October 08, 2015, 08:05:27 AM »
I use white lithium grease on the turnsignal switch with no issues.  Dielectric grease could cause issues.
As for lubing the choke.  Make sure the throttle lever plastic part is clean.  Lube the sliders at the carb with a dry lube.  The cable can be lubed with any cable lube.
I need to replace my cable as it is frayed at the handlebar end
Logged
ammpro
Member
*****
Posts: 72


Clarkdale, Arizona
« Reply #2 on: October 08, 2015, 03:41:01 PM »
I use a dry silicone spray lube for almost everything. Found it very good for the choke cable and that pesky brake lever binding. Specifically, I look for the one for garage doors.
Logged
Frank
Have fun. Be safe. Always set a good example.
jdp
Member
*****
Posts: 446
« Reply #3 on: October 20, 2015, 09:37:11 PM »
I've tried them all the best I found is stuff called dry slide comes in a small bottle and has a 3 inch needle, basically it's a moly dry film lubricant, it can make a Harley clutch cable a 2 finger pull
Logged
hubcapsc
Member
*****
Posts: 16781


upstate

South Carolina
« Reply #4 on: October 21, 2015, 02:57:05 AM »

I've never known a Valkyrie whose choke would stay on
after the cable was lubed...

-Mike
Logged
https://sites.google.com/a/g.clemson.edu/confederate-memorial-day-at-clemson/
DK
Member
*****
Posts: 616


Little Rock
« Reply #5 on: October 21, 2015, 07:16:28 AM »
Quote from: hubcapsc on October 21, 2015, 02:57:05 AM

I've never known a Valkyrie whose choke would stay on
after the cable was lubed...

-Mike

Seems to me that would be good.
Logged
Machinery has a mysterious soul and a mind of its own.
ammpro
Member
*****
Posts: 72


Clarkdale, Arizona
« Reply #6 on: October 21, 2015, 07:20:11 AM »
Agreed. I have never needed to leave the choke on for more than 30 seconds - just long enough to get it started, and a few more seconds so it will keep running.
Logged
Frank
Have fun. Be safe. Always set a good example.
BobB
Member
*****
Posts: 1568


One dragon on the tail of another.
« Reply #7 on: October 22, 2015, 07:13:01 AM »
The choke cable moves within a light colored sleeve that is probably nylon.  The silicone or moly lubricants would work best, stay away from petro based products.  I have never had an issue with this, but there are several moving parts.  Check the slides on the carb banks and the cable between the two slides...
« Last Edit: October 22, 2015, 07:15:07 AM by BobB » Logged
ammpro
Member
*****
Posts: 72


Clarkdale, Arizona
« Reply #8 on: October 22, 2015, 07:14:43 AM »
Good advise.
Logged
Frank
Have fun. Be safe. Always set a good example.
hubcapsc
Member
*****
Posts: 16781


upstate

South Carolina
« Reply #9 on: October 22, 2015, 07:24:09 AM »
Quote from: DK on October 21, 2015, 07:16:28 AM
Quote from: hubcapsc on October 21, 2015, 02:57:05 AM

I've never known a Valkyrie whose choke would stay on
after the cable was lubed...

-Mike

Seems to me that would be good.

It is good if you don't want your choke to be on  Wink

-Mike "I move the lever when I do want it to be on..."
Logged
https://sites.google.com/a/g.clemson.edu/confederate-memorial-day-at-clemson/
F6Dave
Member
*****
Posts: 2263
« Reply #10 on: October 22, 2015, 08:15:08 AM »
I found an aerosol product called CLP Break Free in the gun department at Wal Mart.  It's marketed to clean/lubricate/protect guns, but has lots of other household and automotive uses.  It contains some Teflon and lubricates MUCH better than any other spray-on lube I've tried.
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS