Valkyrie Riders Cruiser Club
July 09, 2025, 04:01:03 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
VRCC Calendar Ad
Pages: [1]   Go Down
Print
Author Topic: Limited Production of Rivco Grab Rails  (Read 1263 times)
JimL
Member
*****
Posts: 1380


Naples,FL


« on: October 22, 2009, 09:39:20 AM »

I just got an email from Stephanie @ Rivco informing me that they are going to do a limited production of the Grab Rails.  They will be taking PRE-PAID orders until November 13, 2009 with expected shipment in February of 2010.

VAL009LR ~ Both the left and right grab rail $99.00 + shipping
VAL009R ~ Right grab rail only $55.00 + shipping

Following is Stephanie's contact info:

Stepahnie Warner
Senior Sales Associate
RIVCO Products,  Inc
Phone: 1-262-763-8222 x 106
Toll Free : 1-888-801-8222 x 106
Fax: 1-262-763-8949
Email: swarner@rivcoproducts.com

WEBSITE: www.rivcoproducts.com
Logged

PAVALKER
Member
*****
Posts: 4435


Retired Navy 22YOS, 2014 Valkyrie , VRCC# 27213

Pittsburgh, Pa


« Reply #1 on: October 22, 2009, 10:31:10 AM »

For those intersted, I found this picture online....


However, I have found that over the years I have managed to aquire my own set of grab rails that adapt to any bike I sit on..... Grin

I think it was previously referred to as a "spare tire"...... but works well in the grab rail application too.
Logged

John                           
JimL
Member
*****
Posts: 1380


Naples,FL


« Reply #2 on: November 02, 2009, 06:09:26 AM »

Bumping this back up to the top just in case there is someone who did not see the original post.
Logged

Doc X
Member
*****
Posts: 65


« Reply #3 on: November 02, 2009, 06:47:28 AM »

PAVALKER, where do the grab rails install on the bike,and will they fit the interstate?
Thanks,
Doc X
PS: PAVALKER, Are you on another bike site also, VTX or Rune?
Logged
PAVALKER
Member
*****
Posts: 4435


Retired Navy 22YOS, 2014 Valkyrie , VRCC# 27213

Pittsburgh, Pa


« Reply #4 on: November 02, 2009, 07:52:04 AM »

I do not have those grab rails on my I/S, but they will fit all Valks.  Rivco had the left grab rail with the Center Stand from what I recall.

Yes, I am on the VTX web site (www.vtxoa.com as PAVTXER) and rarely on the GL1800 board.
Logged

John                           
JimL
Member
*****
Posts: 1380


Naples,FL


« Reply #5 on: November 02, 2009, 08:49:50 AM »

I do not have those grab rails on my I/S, but they will fit all Valks.  Rivco had the left grab rail with the Center Stand from what I recall.

Yes, I am on the VTX web site (www.vtxoa.com as PAVTXER) and rarely on the GL1800 board.

They will fit the Interstate, but since they normally bolt on the sissy bar of the Tourer/Standard which doesn't exist on the Interstate; you will have to drill a hole on the trunk bracket in order to secure the rear bolt.  Not a big deal.
Logged

PAVALKER
Member
*****
Posts: 4435


Retired Navy 22YOS, 2014 Valkyrie , VRCC# 27213

Pittsburgh, Pa


« Reply #6 on: November 02, 2009, 09:11:51 AM »

PAVALKER, where do the grab rails install on the bike,and will they fit the interstate?
Thanks,
Doc X
PS: PAVALKER, Are you on another bike site also, VTX or Rune?


I Googled the install instructions and here is what I got.....  hope this helps....

http://www.rivcoproducts.com/instructions/download/VAL008_Install.pdf
Logged

John                           
Pages: [1]   Go Up
Print
Jump to: