Valkyrie Riders Cruiser Club
March 28, 2026, 10:41:58 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
Inzane 17
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Do you know a good Valkyrie Mechanic in New Jersey or Eastern Pennsylvania?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Do you know a good Valkyrie Mechanic in New Jersey or Eastern Pennsylvania?  (Read 2271 times)
Slowlane1
Member
*****
Posts: 12
« on: July 02, 2024, 07:34:28 PM »
Anyone,

I have a 1999 Honda Valkyrie Interstate that needs a proper diagnosis for a slipping clutch and possible transmission rebuild.  Does anyone know a good mechanic in New Jersey or Eastern PA?  Lower NY State too.  The local Honda dealers do not want to work on bikes that are older than 10 years.  Any help would be greatly appreciated!  Thank you.

Please send me an email: awlutt@yahoo.com
Logged
Hook#3287
Member
*****
Posts: 6898


Brimfield, Ma
« Reply #1 on: July 03, 2024, 04:39:19 AM »
Transmissions in the Valk are somewhat bulletproof.

I'd suspect the clutch, specifically the famous revit failure.

Any  competent motorcycle mechanic can make that repair.

I did it and I'm barely a mechanic.
Logged
98valk
Member
*****
Posts: 13840


South Jersey
« Reply #2 on: July 03, 2024, 08:34:26 AM »
were are u in NJ?
Logged
1998 Std/Tourer, 2007 DR200SE, 1981 CB900C  10speed
1973 Duster 340 4-speed rare A/C, 2001 F250 4x4 7.3L, 6sp

"Our Constitution was made only for a Moral and Religious people. It is wholly inadequate to the goverment of any other."
John Adams 10/11/1798
Chrisj CMA
Member
*****
Posts: 14935


Crestview (Panhandle) Florida
« Reply #3 on: July 03, 2024, 11:29:04 AM »
The only slipping clutch issue with a Valkyrie I have seen was caused by using oil with friction modifiers.  If this turns out to be the case, a flush and correct oil may reverse the problem.
Logged
Hook#3287
Member
*****
Posts: 6898


Brimfield, Ma
« Reply #4 on: July 04, 2024, 08:18:52 PM »
I'm trying to remember the exact symptoms when my clutch rivets went, but it was about 20 years ago, so....

If I remember correctly, the lever was a hard pull in close and although it worked, the clutch seemed to slip some.

Like Jeff stated, the wrong oil will do it.
Logged
HayHauler
Member
*****
Posts: 7569


Pearland, TX
« Reply #5 on: July 10, 2024, 07:44:05 AM »
When the rivets went on mine at around 100k miles, there was some chatter when releasing the clutch.  There were some rivets that sheared off and became lodged between the fiber and metal clutch plates.  This condition caused the clutch to slip due to the rivet separating the plates and reducing the surface area.

My $.01825  Smiley

Hay  Cool
Jimmyt
Logged
VRCC# 28963
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS