Valkyrie Riders Cruiser Club
July 27, 2025, 09:38:24 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > How much brake fluid??
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: How much brake fluid??  (Read 955 times)
JetDriver
Member
*****
Posts: 372


Columbus, OH
« on: September 15, 2013, 08:36:28 PM »
I just drained my front brakes and rebuilt the calipers.  It's back together now, and I'm trying to fill and bleed the lines.  So far I've gone through a 12 oz bottle, and the amount of air coming out of the bleed lines is as much as when I started.  No air is getting in, so I assume I just keep going.  Any tricks, or advice?
Logged
fudgie
Member
*****
Posts: 10613


Better to be judged by 12, then carried by 6.

Huntington Indiana


WWW
« Reply #1 on: September 15, 2013, 09:22:09 PM »
You sure its air coming out? Some times it looks like air getting out but its not. Usually its just air leaking back from your mity-vac. At least this has been my case every time I do mine. If your sure no fluid has gotten below the hole in the resv, your good.
Logged


Now you're in the world of the wolves...
And we welcome all you sheep...

VRCC-#7196
VRCCDS-#0175
DTR
PGR
58Woody
Member
*****
Posts: 71


Chanhassen , Mn.
« Reply #2 on: September 16, 2013, 04:49:39 AM »
You using a mity vac?
If so, Try doing it the old fashioned way.
Also, are your brakes working?
I have changed my clutch and my front brakes fluid and all it took was 1 12oz bottle.
Logged
Be not afraid. Only believe.
9Ball
Member
*****
Posts: 2183


South Jersey
« Reply #3 on: September 16, 2013, 05:40:46 AM »
use a large syringe and surgical tubing and force fresh fluid "UP" from the bleeders to the M/C...just make sure there is adequate room so as not to overflow the reservoir....

also, it occasionally helps to crack open the banjo fittings and allow brake fluid to wet the internal parts...then re-torque to spec.
Logged
VRCC #6897, Joined May, 2000

1999 Standard
2007 Rocket 3
2005 VTX 1300S
JetDriver
Member
*****
Posts: 372


Columbus, OH
« Reply #4 on: September 16, 2013, 09:31:28 PM »
Thanks for the help, guys.  Yes, I was using a miti vac.  It sure LOOKED like the air was coming out of the bleed valve, but it must have been sucking air in from the outside.  58Woody, I did it the old fashioned way and all was good!!  Why do I buy these things when the old fashioned way works?!? Grin
Logged
Raverez
Member
*****
Posts: 699


No good deed goes unpunished

Central New York State
« Reply #5 on: September 16, 2013, 11:27:39 PM »
Quote from: JetDriver on September 16, 2013, 09:31:28 PM
Thanks for the help, guys.  Yes, I was using a miti vac.  It sure LOOKED like the air was coming out of the bleed valve, but it must have been sucking air in from the outside.  58Woody, I did it the old fashioned way and all was good!!  Why do I buy these things when the old fashioned way works?!? Grin


probably like me, to see if works better, or  quicker.
Logged
vanagon40
Member
*****
Posts: 1464

Greenwood, IN
« Reply #6 on: September 17, 2013, 06:56:20 AM »
As the final step, you might try tying the brake lever to the grip and leave it sit overnight.  I used to think this was an old wives' tale as I never noticed any difference with my Valkyrie (but I never completely drained the system).  But when I replaced the brake lines on my '82 SilverWing, I could not believe the difference it made.
Logged
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS