Valkyrie Riders Cruiser Club
November 26, 2025, 01:47:25 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
MarkT Exhaust
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Should I de rust and coat the gas tank while I have it off the bike?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Should I de rust and coat the gas tank while I have it off the bike?  (Read 984 times)
Fritz The Cat
Member
*****
Posts: 1976


"The mountains are calling and I must go."
« on: May 18, 2014, 07:31:37 PM »
Getting ready to pull the carbs and just watched the youtube videos. got through the ones on de rusting and coating the gas tank and gonna get into the carbs next. I can't see any rust in the tank but was wondering if it was worth coating since I have it off the bike. Thanks.
Logged
PAVALKER
Member
*****
Posts: 4435


Retired Navy 22YOS, 2014 Valkyrie , VRCC# 27213

Pittsburgh, Pa
« Reply #1 on: May 18, 2014, 07:59:54 PM »
My opinion.... If you don't see any rust, then why de-rust it?  Coating might actually cause some issues if it doesn't adhere properly.  Normally only when a problem with rust is an issue is when it is cleaned and coated.   Otherwise everyone would do it, or demand it be done to new tanks... Right?

Don't mess with the band while it's playing....
Logged
John                           
pancho
Member
*****
Posts: 2113


Bonanza Arkansas
« Reply #2 on: May 18, 2014, 08:24:08 PM »
I agree with PAVALKER    no use with messing around with an unnecessary complicated procedure,, could cause problems down the road if not done correctly and the coating peels and separates, clogs the filter and other problems. If you don't have rust problems,, no use in trying to fix them.
Logged
The most expensive things you will purchase, are those things you would not have needed if you had listened and obeyed.
Fritz The Cat
Member
*****
Posts: 1976


"The mountains are calling and I must go."
« Reply #3 on: May 19, 2014, 04:52:38 AM »
Thanks, I'll scratch that off my list.
Logged
Attic Rat
Member
*****
Posts: 446


VRCC # 1962

Tulsa, OK


WWW
« Reply #4 on: May 19, 2014, 06:16:54 AM »
Don't  forget to pull the screen out of the tank and clean it before you  put it back on the bike.
Logged
The Attic Rat Performance Works
Fritz The Cat
Member
*****
Posts: 1976


"The mountains are calling and I must go."
« Reply #5 on: May 19, 2014, 06:28:48 AM »
Thanks. Might install a Pringle while I'm at it.
Logged
Momz
Member
*****
Posts: 5702


ABATE, AMA, & MRF rep.
« Reply #6 on: May 19, 2014, 07:32:53 AM »
If you are not sure if the tank has any rust,...pour in a bottle vinegar (with the petcock still installed), any slosh it around for a while, let it sit about an hour, then slosh some more.

Remove the petcock and drain the vinegar and let it sit for a least a day without the petcock and the gas cap open.

Hint: use cheap vinegar, Balsamic is far to expensive  cooldude
Logged

ALWAYS QUESTION AUTHORITY! 

97 Valk bobber, 98 Valk Rat Rod, 2K SuperValk, plus several other classic bikes
Jess from VA
Member
*****
Posts: 30875


No VA
« Reply #7 on: May 19, 2014, 08:48:04 AM »
I've also heard of using kerosene the same way.

Clean the screen.  cooldude
Logged
saab9k
Member
*****
Posts: 92
« Reply #8 on: May 20, 2014, 10:48:39 PM »
The hardware store sell coating for gas tanks, add a cop, rotate the tank around, so all is coated, drain the rest back out. Let sit and dri in the sun for a day. Tank is coated. Gasoline will not cut it.
Logged
Ricky-D
Member
*****
Posts: 5031


South Carolina midlands
« Reply #9 on: May 21, 2014, 08:21:49 AM »
I think your first mistake is assuming what you found is RUST.

Your second big mistake would be coating the inside of the tank.

***
Logged
2000_Valkyrie_Interstate
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS