|
Minnie Miles
|
 |
« on: October 30, 2009, 09:01:59 AM » |
|
Where is a good plase to get a trailer hitch
|
|
|
|
|
Logged
|
|
|
|
kidcatfish
Member
Posts: 120
hold my beer and watch this !!!
Ore City, Texas
|
 |
« Reply #1 on: October 30, 2009, 09:38:00 AM » |
|
I made mine. Quarter inch thick flat metal. Made the sides as seperate from the part that has the ball on it to make it easier to remove the back wheel.
|
|
|
|
|
Logged
|
|
|
|
|
|
kidcatfish
Member
Posts: 120
hold my beer and watch this !!!
Ore City, Texas
|
|
« Reply #3 on: October 30, 2009, 09:59:55 AM » |
|
but look to spend about 4 bills. Yea, thats why I made my own!! I really cheap!! 
|
|
|
|
|
Logged
|
|
|
|
KY,Dave (AKA Misunderstood)
Member
Posts: 4146
Specimen #30838 DS #0233
Williamsburg, KY
|
|
« Reply #4 on: October 30, 2009, 10:05:24 AM » |
|
but look to spend about 4 bills. Yea, thats why I made my own!! I really cheap!! Mine came on it when purchased. Can't get any cheaper or lazier. Didn't have to install or wire it.  |
|
|
|
|
Logged
|
|
|
|
PAVALKER
Member
Posts: 4435
Retired Navy 22YOS, 2014 Valkyrie , VRCC# 27213
Pittsburgh, Pa
|
|
« Reply #5 on: October 30, 2009, 11:36:26 AM » |
|
I posted pics and dimensions on the Tech Board, but here ya go..... I bet a local fab shop could whip you one out in no time. Mine has a ball on it, not a receiver..... but I have considered making the bottom part (receiver) to give me some carry options... Just thinking out-loud....   |
|
|
|
|
Logged
|
John  |
|
|
X Ring
Member
Posts: 3626
VRCC #27389, VRCCDS #204
The Landmass Between Mobile And New Orleans
|
|
« Reply #6 on: October 30, 2009, 12:52:21 PM » |
|
I saved PAVALKER's Hitch Blueprints to my hard drive several months ago. Anyone wants them, send me an email and make sure you tell me you want the hitch plans or you might get the de-smog instructions instead.
|
|
|
|
|
Logged
|
People are more passionately opposed to wearing fur than leather because it's safer to harass rich women than bikers.  |
|
|
Westernbiker
Member
Posts: 1464
1st Place Street Kings National Cruiser Class
Phoenix
|
|
« Reply #7 on: November 02, 2009, 11:54:38 AM » |
|
Does not appear to be enough information to build to print.
|
|
|
|
|
Logged
|
![](http://weathersticker.wunderground.com/weathersticker/miniStates/language/www/US/AZ/Phoenix.gif") May the Lord always ride two up with you! |
|
|
|
Bob E.
|
|
« Reply #8 on: November 02, 2009, 01:17:02 PM » |
|
Does not appear to be enough information to build to print.
There are clearly a couple of dimensions missing. But I was able to use it as a starting point to make a couple templates out of 1/4" foam board from the craft store. I modified the design to support my custom saddlebags. I made it out of 1/4" steel plate, 3" wide. And rather than putting the bolt holes so close to the edge, I put them in the center. Here's a pic before cleaning up and painting.  |
|
|
|
|
Logged
|
|
|
|
|
Sourdough
|
|
« Reply #9 on: November 02, 2009, 03:03:08 PM » |
|
|
|
|
|
|
Logged
|
01 I/S Black/Beige
97 Standard Bumblebee
|
|
|
|
Minnie Miles
|
|
« Reply #10 on: November 03, 2009, 07:43:31 AM » |
|
Thnx .....Miles
|
|
|
|
|
Logged
|
|
|
|
|
