Valkyrie Riders Cruiser Club
November 26, 2025, 12:38:28 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Ultimate Seats Link VRCC Store
Homepage : Photostash : JustPics : Shoptalk : Old Tech Archive : Classifieds : Contact Staff
News: If you're new to this message board, read THIS!
 
VRCC Calendar Ad
Valkyrie Riders Cruiser Club > General > 1500 Tech Board > Need to clean the carburetors, anything I should do while it's apart?
Pages: [1]   Go Down
« previous next »
Send this topic Print
Author Topic: Need to clean the carburetors, anything I should do while it's apart?  (Read 746 times)
Hoss.A
Member
*****
Posts: 4
« on: April 16, 2014, 01:09:41 PM »
Just "inherited" a '97 standard that's been sitting for a couple years and needs a good carb cleaning.  I plan to add some Supertrapp's in the future and was going to replace the LS jets with 38's.  I'll probably desmog it as well for preventative maintenance reasons.

Anything in the carbs or otherwise I should do while it's apart?

Thx.
« Last Edit: April 16, 2014, 01:12:16 PM by Hoss.A » Logged
Thunderbolt
Member
*****
Posts: 3731


Worthington Springs FL.
« Reply #1 on: April 16, 2014, 01:40:01 PM »
Desmog as you said.  Replace the small hoses on the side of each carb that goes to the cut valve.  Replace the hose to #6 that operates the petcock if you still use the OEM petcock.  Replace the intake O-rings.  I had petcock trouble a couple of times and finally relented and bought the non vacuum Pingle and replaced the petcock.  Be sure you tighten all the band clamps on the intake tubes.  If you go to the larger slow jets set the pilot jets all to 1 3/4 turns out from the stop.  If you leave the OEM's in set them to 2 1/4.  Sync when all else is finished.
Easier to get the carb bank out if you remove the support brackets on the rear of the tank, this lets you move it back enough to slide out.  Seems like it comes out the left side easier.  Look in Shoptalk for Quexpress's how to on desmog.  It has pictures.
Logged
DarkSideR
Member
*****
Posts: 1795


To be good, and to do good, is all we have to do.

Pueblo, Colorado


WWW
« Reply #2 on: April 16, 2014, 01:56:11 PM »
The ethanol in gas is hard on rubber. I would suggest replacing any o-rings and gaskets in the Carbs.
Logged
2001 Valkyrie Super Tourer
VRCC#34410
VRCCDS#0263
Westsider
Member
*****
Posts: 716


Fort Worth TX.
« Reply #3 on: April 16, 2014, 04:42:18 PM »
Yep, and check out d-ray smith's videos on youtube, he has some good pointers and tips. Pilot screws and o rings a big must be clean. Can get the pilot orings from redeye tech.
Logged
we'll be there when we get there -   Valkless,, on lookout....
Hoss.A
Member
*****
Posts: 4
« Reply #4 on: April 21, 2014, 05:51:19 AM »
Appreciate everyone's input.  cooldude
Logged
salty1
Member
*****
Posts: 2359


"Flyka"

Spokane, WA or Tucson, AZ
« Reply #5 on: April 21, 2014, 06:11:15 AM »
Might want to consider an electronic fuel shutoff valve while you have it torn down.
http://www.dan-marcrvparts.com/12vomufushof.html
Logged
My rides:
1998 GL1500C, 2000 GL 1500CF,2006 GL 1800 3A
Pages: [1]   Go Up
Send this topic Print
« previous next »
Jump to:  

Theme by Crip Powered by SMF 1.1.20 | SMF © 2013, Simple Machines MySQL | PHP | XHTML | CSS