Carb Sync Guages

[Maldog]

Was  thinking about  gettin a set of  guages for syncin da carbs wold like to get 6 of course most sets ive seen have 4  did the guys  on you tube ive seen with 6 guages make ther own  or can u buy  2 extra guages  also if   ya made your own guage set  can you adivse me as to a list of what u need to make them and the best place  as far as quality and price  to  obtain the   necessary stuff Thanks guys

[mmurffy03]

I have the hondaline 4 guage setup where you do 4 then the other 2





this set works good also

[N8171S]

I bought two sets of 4 from JC Whitney.  These use mercury tubes.  Just hook up 6  They work good.

[whitestroke]

Valkyrie Carb sync harbor freight gauges

Harbor freight, with a set of plastic sprinkler valves from Ace. Under a hundred for everything.

[Maldog]

Hay Thanks Whitestorke ,lol actually  your vid is what got me headin down this road  , can ya help a brother out with some part numbers  for them there guages,was all the tubeing included with the guages or do I need to buy it and if so what size id & od  and that spiniker valve  from Ace  is there a size I need to be aware of  Tha.nks  Bro

[Robert]

whitestroke What did you use as restrictions in line? By the way nice bike and nice setup.

[98valk]

 Twinmax Electronic Carburetor Balancer.

good write up

http://advwisdom.hogranch.com/Wisdom/TBS4Dv1.0.pdf


or morgan carbtune

http://www.carbtune.com/carb.html

[whitestroke]

Vacuum Tubing is 5mm or 13/64
Tubing fits sprinkler valves(restrictors), gauges and manifold.

[Hook#3287]

Twinmax 

Been using one for 10 years or so, easy to use and store.  I remove the battery when not using it, cause they seemed to go dead.

[cantom]

Was  thinking about  gettin a set of  guages for syncin da carbs wold like to get 6 of course most sets ive seen have 4  did the guys  on you tube ive seen with 6 guages make ther own  or can u buy  2 extra guages  also if   ya made your own guage set  can you adivse me as to a list of what u need to make them and the best place  as far as quality and price  to  obtain the   necessary stuff Thanks guys

I just received a Morgan carbtune setup 2 days ago. Will get around to it soon, I swear...

You do 4 then the other 2. A much better setup than using mercury which can get sucked into the cylinders.

I prefer this setup over dial gauges with restrictors.

http://www.carbtune.co.uk/c.com/

[AZdougness]

This is what I came up with after some free time and the help of McMaster-Carr

[matt]

I like the looks of that, How much did it cost?  and part #,s  Please   Thank You

[salty1]

I kept my simple. It has a 4" face and only $24 from Oreillys.

[Patrick]

I like things simple too. I've said this soooooo many times over the years. I use one single plain ole gauge. Since Honda says 1.6 in/hg is their spec, so, this adjustment is no big deal. The single gauge will get you within a needle width which is better/less than .5 in/hg.

[AZdougness]

I like the looks of that, How much did it cost?  and part #,s  Please   Thank You

If I had to do this again I would probably go smaller gauge size and have used a needle valve instead of a ball valve. No doubt it cost much more to do the gauge setup than a manometer.

3941K74 http://www.mcmaster.com/#catalog/119/574/=nwg4gu
50785K26 http://www.mcmaster.com/#catalog/119/36/=nwg5zv
5346K81 http://www.mcmaster.com/#catalog/119/292/=nwg5up
5231K34 http://www.mcmaster.com/#catalog/119/125/=nwg6cr

I highly recommend McMaster to everyone I know, they have excellent products, as well as fantastic customer service.