Side stand "Special" bolt.......

[Stanley Steamer]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

[Skinhead]

You are correct.  Pretty good for a johnny reb.

[Stanley Steamer]

You are correct.  Pretty good for a johnny reb.

.........I would have probably had to "cross" the line if I had of been around back then......

[Ricky-D]

That bolt will last longer than you'll be riding.

Especially if you lubricate it once in a while.

***

[Stanley Steamer]

That bolt will last longer than you'll be riding.

Especially if you lubricate it once in a while.

***

will KY work?...........

[Bone]

My bolt was bent from the floor jack using it as a stop
I did replace it before it broke.

[Valkpilot]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

If you're looking for the bolt that the spring hooks to, it's #10 in this diagram:

http://www.hdlparts.com/fiche_section_detail.asp?section=2552469&category=Motorcycles&make=Honda&year=2000&fveh=132671

The bolt you referred to holds the kickstand in place and is its pivot.

[Chrisj CMA]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

If you're looking for the bolt that the spring hooks to, it's #10 in this diagram:

http://www.hdlparts.com/fiche_section_detail.asp?section=2552469&category=Motorcycles&make=Honda&year=2000&fveh=132671

The bolt you referred to holds the kickstand in place and is its pivot.

I think you meant #11

[Stanley Steamer]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

If you're looking for the bolt that the spring hooks to, it's #10 in this diagram:

http://www.hdlparts.com/fiche_section_detail.asp?section=2552469&category=Motorcycles&make=Honda&year=2000&fveh=132671

The bolt you referred to holds the kickstand in place and is its pivot.

Well..........@%$@$#!!!!.....do I need part #30 also??....or does just the end break off when it breaks?...I think that is what I did last time......I wasn't even on the right microfiche....that's what I get for being too lazy to go LOOK at the bike and see where it was attached...... ............Thanks

[Stanley Steamer]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

If you're looking for the bolt that the spring hooks to, it's #10 in this diagram:

http://www.hdlparts.com/fiche_section_detail.asp?section=2552469&category=Motorcycles&make=Honda&year=2000&fveh=132671

The bolt you referred to holds the kickstand in place and is its pivot.

I think you meant #11

It's part #10 on the '99 I/S microfische.......I see on the 2000 CT models it was part #11

[Valkpilot]

is it part # 5 in this diagram??...and the nut..#7?......I think I mistakenly ordered part # 6 one time.......I do have the spring on hand.....with my '99 I/S getting on up there, I'm afraid that bolt is weak by now..... :

http://www.hdlparts.com/fiche_section_detail.asp?section=4223971&category=Motorcycles&make=Honda&year=1999&fveh=188145

If you're looking for the bolt that the spring hooks to, it's #10 in this diagram:

http://www.hdlparts.com/fiche_section_detail.asp?section=2552469&category=Motorcycles&make=Honda&year=2000&fveh=132671

The bolt you referred to holds the kickstand in place and is its pivot.

I think you meant #11

Yep.